Fred (Guest)
Fred (Guest)
I have my DVR 7202 wired into my truck so it turns on when I start the truck. But the date keeps defaulting back to Sept. 5, 2012 a few days after I reset it to the current date. Any idea why?
 
road
road
I have my DVR 7202 wired into my truck so it turns on when I start the truck. But the date keeps defaulting back to Sept. 5, 2012 a few days after I reset it to the current date. Any idea why?
 
Be sure you pressed [OK] button after you changed the Date/Time setting.
To set the date/time, please follow below steps
 
1. Press [POWER] button to power on the system.
2. Press [MENU] button to settings menu
3. Press [MODE] button to system settings, then press [DOWN] button to select "Date/Time" and press [OK] button to confirm selection.
4. Press [UP] or [DOWN] button to change "Month" then press [MODE] button to switch to "Day"
5. Press [UP] or [DOWN] button to change "Day" then press [MODE] button to "Year"
6. Do the same steps to complete "Time" setting. Finally,press [OK] button to save your "Date/Time" settings.
7. Press [MENU] button to exit settings.
 
 
 
scott (Guest)
scott (Guest)
my playback videos are jumping or flickering
 
Rockyman (Guest)
Rockyman (Guest)
Follow below steps to set the date/time
 
1. Press [POWER] button to power on the system.
2. Press [MENU] button to settings menu
3. Press [MODE] button to system settings, then press [DOWN] button to select "Date/Time" and press [OK] button to confirm.
4. Press [UP] or [DOWN] button to change "Month" then press [MODE] button switch to "Day"
5. Press [UP] or [DOWN] button to change "Day" then press [MODE] button switch to "Year"
6. Press [UP] or [DOWN] button to change "Hour" then press [MODE] button switch to "Minute"
7. Press [UP] or [DOWN] button to change "Minute".
6. Finally, press [OK] button to save your "Date/Time" settings.
7. Press [MENU] button to exit settings.
 
Dev (Guest)
Dev (Guest)
i've just returned from a long trip and every time I've put in all the settings such as date, looping etc. and following putting in "OK" after each request, my L-640 loses all my settings when unplugged. So I had a plug that was always hot and used that and it worked fine for the rest of the 4 day drive. This can't always be the case.
Can you help.
Thanks
Dev
 
road
road
i've just returned from a long trip and every time I've put in all the settings such as date, looping etc. and following putting in "OK" after each request, my L-640 loses all my settings when unplugged. So I had a plug that was always hot and used that and it worked fine for the rest of the 4 day drive. This can't always be the case.
Can you help.
Thanks
Dev
 
To set the date/time, please follow below steps
 
1. Press [POWER] button to power on the system.
2. Press [MENU] button to settings menu
3. Press [MODE] button to system settings, then press [DOWN] button to select "Date/Time" and press [OK] button to confirm.
4. Press [UP] or [DOWN] button to change "Month" then press [MODE] button switch to "Day"
5. Press [UP] or [DOWN] button to change "Day" then press [MODE] button switch to "Year"
6. Do the same steps to complete "Hour" and "Minute" setting then press [OK] button to save your "Date/Time" settings.
7. Press [MENU] button to exit settings.
 
 
Mark (Guest)
Mark (Guest)
Purchased dvr this past September and attempted to view recording of trip. Well the dvr locked up, will not turn off (battery has full charge) and screen on dvr is a series of dashes. Nothing works. Please advise.
 
Mark (Guest)
Mark (Guest)
Purchased dvr this past September and attempted to view recording of trip. Well the dvr locked up, will not turn off (battery has full charge) and screen on dvr is a series of dashes. Nothing works. Please advise.
 
wrsearle
wrsearle
We bought Road Mate DVR at the Ft. Myers FL RV show in January 2016 from a Tawainese couple. We have used the unit everyday, but for some reason, it will no longer turn on and there is no power to the unit. We hooked it up via the USB to the computer, but still nothing. We were never provided with any manuals. Please advise.
 
Ron (Guest)
Ron (Guest)
I bought a unit 2 years ago and it worked fine till the fall. For some reason, it will no longer turn on and there is no power to the unit. We hooked it up via the USB to the computer, but still nothing. We were never provided with any manuals. Please advise.
 
harold (Guest)
harold (Guest)
purchased my road mate RM 12087 in Vermont last summer from a vendor at the escapes show. All of a sudden the date goes back to 2012 and will not reset. Please advise how to fix the problem.
 

Message
Nickname *
Your Email Address *
Message *
Validation Code *